v8.5.0

版本发布时间: 2020-09-14 17:07:19

arendst/Tasmota最新发布版本:v14.2.0(2024-08-14 20:52:35)

RELEASE NOTES

Migration Information

See migration path for instructions how to migrate to a major version. Pay attention to the following version breaks due to dynamic settings updates:

Migrate to Sonoff-Tasmota 3.9.x
Migrate to Sonoff-Tasmota 4.x
Migrate to Sonoff-Tasmota 5.14
Migrate to Sonoff-Tasmota 6.x
Migrate to Tasmota 7.x

--- Major change in parameter storage layout ---

Migrate to Tasmota 8.1
Migrate to Tasmota 8.x

While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v8.1.0 Doris the Settings are re-allocated in such a way that fallback is only allowed and possible to release v7.2.0 Constance. Once at v7.2.0 you're on your own when downgrading even further.

Supported Core versions

This release will be supported from ESP8266/Arduino library Core version 2.7.4.1 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.

Support of Core versions before 2.7.1 has been removed.

Support of TLS

To save resources when TLS is enabled mDNS needs to be disabled. In addition to TLS using fingerprints now also user supplied CA certs and AWS IoT is supported. Read full documentation

Initial configuration tools

For initial configuration this release supports Webserver based WifiManager or Serial based command interface only. Support for WPS and SmartConfig has been removed.

Provided Binary Downloads

The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.1.

tasmota.bin = The Tasmota version with most drivers. RECOMMENDED RELEASE BINARY
tasmota-BG.bin to tasmota-TW.bin = The Tasmota version in different languages.
tasmota-lite.bin = The Lite version without most drivers and sensors.
tasmota-knx.bin = The Knx version without some features but adds KNX support.
tasmota-sensors.bin = The Sensors version adds more useful sensors.
tasmota-ir = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features.
tasmota-display.bin = The Display version without Energy Monitoring but adds display support.
tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version.
tasmota-minimal.bin = The Minimal version allows intermediate OTA uploads to support larger versions and does NOT change any persistent parameter. This version should NOT be used for initial installation.

The attached binaries can also be downloaded from http://ota.tasmota.com/tasmota/release for ESP8266 or http://ota.tasmota.com/tasmota32/release for ESP32. The links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin

List of embedded modules.

Complete list of available feature and sensors.

Changelog

Version 8.5.0 Hannah

Remove support for direct upgrade from versions before 6.6.0.11 to versions after 8.4.0.1
Change references from http://thehackbox.org/tasmota/ to http://ota.tasmota.com/tasmota/
Change triple-mode TLS via configuration in a single firmware (TLS AWS IoT, Letsencrypt and No-TLS)
Change White blend mode to using command SetOption 105 instead of RGBWWTable
Fix ESP32 PWM range
Fix display power control (#9114)
Fix energy total counters (#9263, #9266)
Add command SetOption102 0/1 to set Baud rate for Teleinfo communication (0 = 1200 or 1 = 9600)
Add command SetOption103 0/1 to set TLS mode when TLS is selected
Add command SetOption104 1 to disable all MQTT retained messages
Add command SetOption106 1 to create a virtual White ColorTemp for RGBW lights
Add command SetOption107 0/1 to select virtual White as (0) Warm or (1) Cold
Add command SetOption108 0/1 to enable Teleinfo telemetry into Tasmota Energy MQTT (0) or Teleinfo only (1)
Add command SetOption109 1 to force gen1 Alexa mode, for Echo Dot 2nd gen devices only
Add command Restart 2 to halt system. Needs hardware reset or power cycle to restart (#9046)
Add command PowerDelta1 to PowerDelta3 to trigger on up to three phases (#9134)
Add Zigbee options to ZbSend Config and ReadCondig
Add Zigbee better support for IKEA Motion Sensor
Add Zigbee web gui widget for Battery and Temp/Humidity/Pressure sensors
Add Zigbee web ui for power metering plugs
Add better configuration corruption recovery (#9046)
Add virtual CT for 4 channels lights, emulating a 5th channel
Add support for DYP ME007 ultrasonic distance sensor by Janusz Kostorz (#9113)
Add ESP32 Analog input support for GPIO32 to GPIO39
Add experimental support for ESP32 TTGO Watch and I2S Audio by Gerhard Mutz