v8.3.1
版本发布时间: 2020-05-18 22:01:24
arendst/Tasmota最新发布版本:v14.2.0(2024-08-14 20:52:35)
RELEASE NOTES
Migration Information
See migration path for instructions how to migrate to a major version. Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14
- Migrate to Sonoff-Tasmota 6.x
- Migrate to Tasmota 7.x
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.1
- Migrate to Tasmota 8.x
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v8.1.0 Doris the Settings are re-allocated in such a way that fallback is only allowed and possible to release v7.2.0 Constance. Once at v7.2.0 you're on your own when downgrading even further.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.1 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
Although it might still compile on previous Core versions all support will be removed in the near future.
Support of TLS
To save resources when TLS is enabled mDNS needs to be disabled. In addition to TLS using fingerprints now also user supplied CA certs and AWS IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface only. Support for WPS and SmartConfig has been removed.
Provided Binary Downloads
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.1.
- tasmota.bin = The Tasmota version with most drivers. RECOMMENDED RELEASE BINARY
- tasmota-BG.bin to tasmota-TW.bin = The Tasmota version in different languages.
- tasmota-lite.bin = The Lite version without most drivers and sensors.
- tasmota-knx.bin = The Knx version without some features but adds KNX support.
- tasmota-sensors.bin = The Sensors version adds more useful sensors.
- tasmota-ir = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support.
- tasmota-minimal.bin = The Minimal version allows intermediate OTA uploads to support larger versions and does NOT change any persistent parameter. This version should NOT be used for initial installation.
List of embedded modules.
Complete list of available feature and sensors.
Changelog
Version 8.3.1 Fred
- Change Hass discovery from using Template or Module name to new Device name (#8462)
- Change KNX pow function to approximative pow saving 5k of code space
- Change Mutichannel Gas sensor pow function to approximative pow saving 5k of code space
- Change Quick Power Cycle detection from 4 to 7 power interrupts (#4066)
- Fix default state of
SetOption73 0
for button decoupling and send multi-press and hold MQTT messages - Add command
DeviceName
defaults to FriendlyName1 and replaces FriendlyName1 in GUI
Version 8.3.0 Fred
- Breaking Change Device Groups multicast address and port (#8270)
- Change PWM implementation to Arduino #7231 removing support for Core versions before 2.6.3
- Change default PWM Frequency to 977 Hz from 880 Hz
- Change minimum PWM Frequency from 100 Hz to 40 Hz
- Change flash access removing support for any Core before 2.6.3
- Change HM-10 sensor type detection and add features (#7962)
- Change light scheme 2,3,4 cycle time speed from 24,48,72,... seconds to 4,6,12,24,36,48,... seconds (#8034)
- Change remove floating point libs from IRAM
- Change remove MQTT Info messages on restart for DeepSleep Wake (#8044)
- Change IRremoteESP8266 library updated to v2.7.6
- Change HAss discovery by Federico Leoni (#8370)
- Fix possible Relay toggle on (OTA) restart
- Fix PWM flickering during wifi connection (#8046)
- Fix Zigbee sending wrong Sat value with Hue emulation
- Fix Zigbee crash with Occupancy sensor (#8089)
- Add Zigbee command
ZbRestore
to restore device configuration dumped withZbStatus 2
- Add Zigbee command
ZbUnbind
- Add Zigbee command
ZbBindState
andmanuf
attribute - Add Zigbee command
ZbConfig
and configuration in Settings - Add commands
CounterDebounceLow
andCounterDebounceHigh
to control debouncing (#8021) - Add commands
NrfPage
,NrfIgnore
,NrfScan
andNrfBeacon
to NRF24 Bluetooth driver (#8075) - Add commands
GlobalTemp
andGlobalHum
to init sensor data (#8152) - Add command
SO
as shortcut for commandSetOption
- Add command
SetOption41 <x>
to force sending gratuitous ARP everyseconds - Add command
SetOption73 1
for button decoupling and send multi-press and hold MQTT messages by Federico Leoni (#8235) - Add command
SetOption90 1
to disable non-json MQTT messages (#8044) - Add command
SetOption91 1
to enable fading at startup / power on - Add command
SetOption92 1
to set PWM Mode from regular PWM to ColorTemp control (Xiaomi Philips ...) - Add command
SetOption93 1
to control caching of compressed rules - Add command
Sensor10 0/1/2
to control BH1750 resolution - 0 = High (default), 1 = High2, 2 = Low (#8016) - Add command
Sensor10 31..254
to control BH1750 measurement time which defaults to 69 (#8016) - Add command
Sensor18 0..32000
to control PMS5003 sensor interval to extend lifetime by Gene Ruebsamen (#8128) - Add command
DevGroupName
to specify up to four Device Group Names (#8087) - Add command
DevGroupSend
to send an update to a Device Group (#8093) - Add command
Ping
(#7176) - Add command
Palette
to add the ability to specify a palette of colors (#8150) - Add support for unreachable (unplugged) Zigbee devices in Philips Hue emulation and Alexa
- Add support for 64x48 SSD1306 OLED (#6740)
- Add support for Seven Segment display using HT16K33 (#8116)
- Add support for up to four MQTT GroupTopics (#8014)
- Add support for longer template names
- Add support for an iAQ sensor (#8107)
- Add support for AS3935 Lightning Sensor by device111 (#8130)
- Add console command history (#7483, #8015)
- Add quick wifi reconnect using saved AP parameters when
SetOption56 0
(#3189) - Add more accuracy to GPS NTP server (#8088)
- Add support for analog anemometer by Matteo Albinola (#8283)
- Add support for OpenTherm by Yuriy Sannikov (#8373)
- Add support for Thermostat control by arijav (#8212)
- Add experimental basic support for Tasmota on ESP32 based on work by Joerg Schueler-Maroldt
- Add automatic compression of Rules to achieve ~60% compression by Stefan Hadinger
- Add rule trigger at root level like
on loadavg<50 do power 2 endon
afterstate
command
1、 tasmota-BG.bin 594.03KB
2、 tasmota-BG.bin.gz 412.15KB
3、 tasmota-BR.bin 588.92KB
4、 tasmota-BR.bin.gz 410.93KB
5、 tasmota-CN.bin 587.73KB
6、 tasmota-CN.bin.gz 411.11KB
7、 tasmota-CZ.bin 588.78KB
8、 tasmota-CZ.bin.gz 411.12KB
9、 tasmota-DE.bin 588.66KB
10、 tasmota-DE.bin.gz 410.81KB
11、 tasmota-display.bin 546.97KB
12、 tasmota-display.bin.gz 376.7KB
13、 tasmota-ES.bin 588.73KB
14、 tasmota-ES.bin.gz 410.9KB
15、 tasmota-FR.bin 588.95KB
16、 tasmota-FR.bin.gz 410.92KB
17、 tasmota-GR.bin 592.03KB
18、 tasmota-GR.bin.gz 411.92KB
19、 tasmota-HE.bin 589.75KB
20、 tasmota-HE.bin.gz 411.13KB
21、 tasmota-HU.bin 589KB
22、 tasmota-HU.bin.gz 411.04KB
23、 tasmota-ir.bin 566.64KB
24、 tasmota-ir.bin.gz 386.45KB
25、 tasmota-ircustom.bin 687.39KB
26、 tasmota-ircustom.bin.gz 469.11KB
27、 tasmota-IT.bin 588.92KB
28、 tasmota-IT.bin.gz 410.81KB
29、 tasmota-knx.bin 583.38KB
30、 tasmota-knx.bin.gz 405.05KB
31、 tasmota-KO.bin 588.53KB
32、 tasmota-KO.bin.gz 411.08KB
33、 tasmota-lite.bin 471.86KB
34、 tasmota-lite.bin.gz 330.74KB
35、 tasmota-minimal.bin 377.08KB
36、 tasmota-minimal.bin.gz 268.36KB
37、 tasmota-NL.bin 588.36KB
38、 tasmota-NL.bin.gz 410.71KB
39、 tasmota-PL.bin 589.13KB
40、 tasmota-PL.bin.gz 411.1KB
41、 tasmota-PT.bin 589.27KB
42、 tasmota-PT.bin.gz 411.02KB
43、 tasmota-RO.bin 588.56KB
44、 tasmota-RO.bin.gz 410.83KB
45、 tasmota-RU.bin 592.55KB
46、 tasmota-RU.bin.gz 411.94KB
47、 tasmota-SE.bin 588.44KB
48、 tasmota-SE.bin.gz 410.82KB
49、 tasmota-sensors.bin 616.59KB
50、 tasmota-sensors.bin.gz 427.81KB
51、 tasmota-SK.bin 588.84KB
52、 tasmota-SK.bin.gz 411.12KB
53、 tasmota-TR.bin 588.69KB
54、 tasmota-TR.bin.gz 410.97KB
55、 tasmota-TW.bin 587.61KB
56、 tasmota-TW.bin.gz 410.99KB
57、 tasmota-UK.bin 593.64KB
58、 tasmota-UK.bin.gz 412.1KB
59、 tasmota.bin 587.72KB
60、 tasmota.bin.gz 410.24KB