v8.2.0
版本发布时间: 2020-03-21 18:06:31
arendst/Tasmota最新发布版本:v14.4.1(2024-12-15 21:46:59)
RELEASE NOTES
Migration Information
See migration path for instructions how to migrate to a major version. Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14
- Migrate to Sonoff-Tasmota 6.x
- Migrate to Tasmota 7.x
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.1
- Migrate to Tasmota 8.x
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v8.1.0 Doris the Settings are re-allocated in such a way that fallback is only allowed and possible to release v7.2.0 Constance. Once at v7.2.0 you're on your own when downgrading even further.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.6.3 + 372a3ec due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
Although it might still compile on previous Core versions all support will be removed in the near future.
Support of TLS
To save resources when TLS is enabled mDNS needs to be disabled. In addition to TLS using fingerprints now also user supplied CA certs and AWS IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface only. Support for WPS and SmartConfig has been removed.
Provided Binary Downloads
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.6.3 + 372a3ec.
- tasmota.bin = The Tasmota version with most drivers. RECOMMENDED RELEASE BINARY
- tasmota-BG.bin to tasmota-TW.bin = The Tasmota version in different languages.
- tasmota-lite.bin = The Lite version without most drivers and sensors.
- tasmota-knx.bin = The Knx version without some features but adds KNX support.
- tasmota-sensors.bin = The Sensors version adds more useful sensors.
- tasmota-ir = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support.
- tasmota-minimal.bin = The Minimal version allows intermediate OTA uploads to support larger versions and does NOT change any persistent parameter. This version should NOT be used for initial installation.
List of embedded modules.
Complete list of available feature and sensors.
Changelog
Version 8.2.0 Elliot
- Change default my_user_config.h driver and sensor support removing most sensors and adding most drivers to tasmota.bin
- Change DHT driver (#7468, #7717)
- Change Lights: simplified gamma correction and 10 bits internal computation
- Change commands
Prefix
,Ssid
,StateText
,NTPServer
, andFriendlyName
displaying all items - Change Zigbee command prefix from
Zigbee*
toZb*
- Change MQTT message size with additional 200 characters
- Change display of some date and time messages from "Wed Feb 19 10:45:12 2020" to "2020-02-19T10:45:12"
- Change IRremoteESP8266 library updated to v2.7.4
- Fix
PowerDelta
zero power detection (#7515) - Fix
White
added to light status (#7142) - Fix
WakeUp <x>
ignores provided value (#7473) - Fix
RGBWWTable
ignored (#7572) - Fix commands
Display
andCounter
from overruling command processing (#7322) - Fix Sonoff Bridge, Sc, L1, iFan03 and CSE7766 serial interface to forced speed, config and disable logging
- Fix Improved fade linearity with gamma correction
- Fix PWM flickering at low levels (#7415)
- Fix LCD line and column positioning (#7387)
- Fix Display handling of hexadecimal escape characters (#7387)
- Fix exception 9 restart on log message in Ticker interrupt service routines NTP, Wemos and Hue emulation (#7496)
- Fix Hass sensor discovery by Federico Leoni (#7582, #7548)
- Fix MaxPower functionality (#7647)
- Fix relation between Wifi RSSI and signal strength
- Add command
SetOption79 0/1
to enable reset of counters at teleperiod time by Andre Thomas (#7355) - Add command
SetOption82 0/1
to limit the CT range for Alexa to 200..380 - Add command
SetOption84 0/1
to send AWS IoT device shadow updates (alternative to retained) - Add commands
SetOption85 0/1
andDevGroupShare
supporting UDP Group command usingGroupTopic
without MQTT by Paul Diem (#7790) - Add command
SetOption86 0/1
for PWM dimmer to turn brightness LED's off 5 seconds after last change - Add command
SetOption87 0/1
for PWM dimmer to turn red LED on when powered off - Add command
SetOption88 0/1
for PWM dimmer to let buttons control remote devices - Add command
SetOption89 0/1
for Zigbee distinct MQTT topics per device for SENSOR, allowing retained messages (#7835) - Add command
ShutterButton <parameters>
to control shutter(s) by to-scho (#7403) - Add commands
SwitchMode 8
ToggleMulti,SwitchMode 9
FollowMulti andSwitchMode 10
FollowMultiInverted (#7522) - Add commands
SwitchMode 11
PushHoldMulti andSwitchMode 12
PushHoldInverted (#7603) - Add commands
SwitchMode 13
PushOn andSwitchMode 14
PushOnInverted (#7912) - Add command
Buzzer -1
for infinite mode and commandBuzzer -2
for following led mode (#7623) - Add command
HumOffset -10.0 .. 10.0
to set global humidity sensor offset (#7934) - Add support for
AdcParam
parameters to control ADC0 Current Transformer Apparent Power formula by Jodi Dillon (#7100) - Add optional parameter
<startcolor>
to commandScheme <scheme>, <startcolor>
to control initial start color - Add web page sliders when
SetOption37 128
is active allowing control of white(s) - Add SerialConfig to
Status 1
- Add BootCount Reset Time as BCResetTime to
Status 1
- Add WifiPower to
Status 5
- Add most SetOptions as defines to my_user_config.h
- Add optional Wifi AccessPoint passphrase define WIFI_AP_PASSPHRASE in my_user_config.h (#7690)
- Add SoftwareSerial to CSE7766 driver allowing different GPIOs (#7563)
- Add rule trigger on one level deeper using syntax with two
#
likeon zbreceived#vibration_sensor#aqaracubeside=0 do ...
- Add Zigbee attribute decoder for Xiaomi Aqara Cube
- Add
ZbZNPReceived
andZbZCLReceived
being published to MQTT whenSetOption66 1
- Add Zigbee enhanced commands decoding, added
ZbPing
- Add Zigbee features and improvements
- Add Zigbee support for Hue emulation by Stefan Hadinger
- Add HAss Discovery support for Button and Switch triggers by Federico Leoni (#7901)
- Add Dew Point to Temperature and Humidity sensors
- Add optional support for Prometheus using file xsns_91_prometheus.ino (#7216)
- Add support for gzipped binaries
- Add support for Romanian language translations by Augustin Marti
- Add support for sensors DS18x20 and DHT family on Shelly 1 and Shelly 1PM using Shelly Add-On adapter (#7469)
- Add support to BMP driver to enter reset state (sleep enable) when deep sleep is used in Tasmota
- Add support for DS1624, DS1621 Temperature sensor by Leonid Myravjev
- Add support for NRF24L01 as BLE-bridge for Mijia Bluetooth sensors by Christian Baars (#7394)
- Add support for MI-BLE sensors using HM-10 Bluetooth 4.0 module by Christian Staars (#7683)
- Add support for FiF LE-01MR energy meter by saper-2 (#7584)
- Add support for Sensors AHT10 and AHT15 by Martin Wagner (#7596)
- Add support for Wemos Motor Shield V1 by Denis Sborets (#7764)
- Add support for La Crosse TX23 Anemometer by Norbert Richter (#3146, #7765)
- Add support for Martin Jerry/acenx/Tessan/NTONPOWER SD0x PWM dimmer switches by Paul Diem (#7791)
- Add support for UDP Group control without MQTT by Paul Diem (#7790)
- Add support for Jarolift rollers by Keeloq algorithm
- Add support for MaxBotix HRXL-MaxSonar ultrasonic range finders by Jon Little (#7814)
- Add support for HDC1080 Temperature and Humidity sensor by Luis Teixeira (#7888)
- Add support for ElectriQ iQ-wifiMOODL RGBW light by Ian King (#7947)
1、 tasmota-BG.bin 583.95KB
2、 tasmota-BR.bin 578.84KB
3、 tasmota-CN.bin 577.64KB
4、 tasmota-CZ.bin 578.72KB
5、 tasmota-DE.bin 578.59KB
6、 tasmota-display.bin 537.67KB
7、 tasmota-ES.bin 578.7KB
8、 tasmota-FR.bin 578.88KB
9、 tasmota-GR.bin 581.98KB
10、 tasmota-HE.bin 579.67KB
11、 tasmota-HU.bin 578.92KB
12、 tasmota-ir.bin 556.33KB
13、 tasmota-ircustom.bin 674.31KB
14、 tasmota-IT.bin 578.47KB
15、 tasmota-knx.bin 579.75KB
16、 tasmota-KO.bin 578.48KB
17、 tasmota-lite.bin 466.14KB
18、 tasmota-minimal.bin 374.48KB
19、 tasmota-NL.bin 578.27KB
20、 tasmota-PL.bin 579.03KB
21、 tasmota-PT.bin 579.2KB
22、 tasmota-RO.bin 578.47KB
23、 tasmota-RU.bin 582.52KB
24、 tasmota-SE.bin 578.36KB
25、 tasmota-sensors.bin 597.36KB
26、 tasmota-SK.bin 578.78KB
27、 tasmota-TR.bin 578.56KB
28、 tasmota-TW.bin 577.52KB
29、 tasmota-UK.bin 583.58KB
30、 tasmota.bin 577.64KB